Rotor-Tech Hydra-Lectrik TEG Pumps

Hydra-Lectrik Design Concept

Most dehydrators using electric pumps expel high pressure, wet glycol from the contactor through a throttling valve. This valuable energy source is wasted and the expelled glycol can be environmentally unsound.

Rotor-Tech's design concept harnesses this energy to power a hydraulic rotary gear motor that operates a specially designed gear pump approximately volumetrically equal to the motor. Then, by adding a small electric motor to overcome mechanical and hydraulic friction, the combined unit...the Hydra-Lectrik...can operate at a desired speed to attain a specified flow rate for the system. No contactor gas is used.

Because of the low electrical power requirement, the Hydra-Lectrik can operate in many locations where there is insufficient electrical service to run a pump solely dependent on electrical power. Alternative plunger pumps generally need more expensive 480 VAC, 3-phase power...not always available in remote locations. It is also desirable to control pump and motor speed with a variable frequency drive (inverter) which is much less expensive for the low power small electric motors used to drive the Hydra-Lectrik.

Hydra-Lectrik Pump

Designed for Today's (TEG) Dehydration Systems

	*FEATURES*
	Double Face electric Drive Motor Improves balance, runs smoother and is easy to maintain. Dual Powered Hydraulically by return wet high pressure glycol. Electrically by a small electric motor. Vibration-Free No pulsation dampeners required. Economical Can pay for itself when replacing an energy exchange pump in 2 to 4 months. Pays for itself when replacing a standard electric drive pump in 12 to 24 months. Saves up to 83% of electrical power vs. conventional electric pumps.	Flow Rates from 10 GPH to 10,000 GPH Can be easily and economically controlled by a small variable frequency motor controller (Inverter). Compact and Lightweight 80% smaller than alternative pump systems of comparable performance. Rotary Gear Design Sustains high efficiency throughout pump life. Consistent performance. No reciprocating pump parts. No dependency on elastomeric parts subject to wear and deterioration. No Slides, piston, check valves, or O-rings to be replaced. Simple and Easily Serviced With Easy Access Reduces routine maintenance time. The Hydra-Lectrik pump uses no gas
	Stable Flow...Positive Displacement	Hydra-Lectrik Pump...Your Best Alternative to Help Meet VOC and BETX Emission Standards.

Hydra-Lectrik - Environmentally Friendly

The first step in meeting new EPA and state mandated VOC and BETX emission standards is to install speed controlled-electric drive glycol pumps...like the Rotor-Tech Hydra-Lectrik. This eliminates contactor gas consumption often wasted to the atmosphere and allows glycol circulation to be controlled to an optimum rate.

Like all Rotor-Tech glycol pumps, the Hydra-Lectrik pump space-saving configuration is easy to install and maintain. It operates smooth and whisper quiet while providing flow rates from 10 to 10,000 GPH at pressures in excess of 2,000 PSIG.

Hydra-Lectrik - Pays For Itself

Low initial cost and less installation, operating and maintenance costs, make Rotor-Tech pumps your efficient alternative for today's dehydrator glycol pumping.

When replacing an energy exchange pump, the Hydra-Lectrik can pay for itself in 2 to 4 months! When replacing a standard electric drive pump, it pays for itself in 12 to 24 months. Nobody offers a glycol pump that can beat that...nobody!

The Hydra-Lectrik costs less to purchase, install, operate and maintain. It is smaller and 80% lighter than pumps of comparable performance. Rotor-Tech's Hydra-Lectrik represents the state-of-the-art in glycol specialty pump engineering, energy conservation and environmental compliance.

Automatic Controller with VF Driver (Interver)

Automatic Controller with VF Drive (Inverter)

Rotor-Tech offers and recommends an Automatic Controller System. It operates all the pump start-up and shut-down circuits and incorporates a safety flow switch to automatically close the high pressure return valve in case of low-flow or no-flow in the dry glycol suction line. The speed controller (Inverter) is included in this enclosure if so ordered.

Hydra-Lectrik pump

Double-ended "C" Face Mounting is Simple

This 10 HP, three-phase, 480 VAC Hydra-Lectrik pump space-saving configuration is easy to install and maintain. It operates whisper quiet and vibration-free with no pulsation dampeners.


Skid Mounted 1/2 HP, Single-Phase, 110V Motor

Back To Top

We Now Take Visa® and Master Card®
We Now Take Visa^® & Master Card^®